(The 9000Pro Instrument Definition File):

http://www.geocities.com/pipelinerr//9000PRO_INST_DEF_FILE.html


 

PSR 9000 

Steps for editing a song 

  1. Record a song in Multi-Track Record
  2. Save the song either to a floppy disk or if one is installed to the Hard Disk.
  3. After the song has been saved: press Song I (looking on page 10 of Owner’s manual it is located under the “5”)

 

IF the song was saved to the Hard Disk follow steps below under

“HD Instructions”  

  1. After pressing Song I screen will show song/s on disk.
  2. Select the song that you wish to edit by pressing the button to the side of title of the song. (Refer to bottom of page 30 in Owner’s manual for illustration of what the screen will look like. The buttons I’m referring to are the lettered buttons to the left and right of the screen)
  3. Press Song Recording button (Digital Recording)
  4. Press Song Creator
  5. Press Current Song
  6. Press Multi-Track Record

 

NOTE: Refer to Owner’s Manual page 80 for illustration of Screen referred to in the following steps: 

  1. Press REC MODE (“Rec Mode” is located in upper left corner of screen)
  2. Select “PUNCH IN” under Record Mode at the bottom of the screen.
  3. Select “Auto Set” under Punch-in Trigger at bottom of screen.
  4. Select the number of measures you would like to edit. (It would be a good idea to give yourself a couple of measures of lead in prior to the measure that you wish to edit.) Select Measure number above the words “IN” and “OUT” – located in the lower right corner of the screen)
  5. Press OK

NOTE: If there are any voice changes or effect changes to be made as part of the edit that you wish to do make those changes at this time.

15. Press the “Next” button

  1. Press the Start/Stop button to begin recording/edit

16.Play/edit the recording (play new material)

  1. Press “Next” to save

 

++++++++++++++++++++++++++++++++++++++++++++++

HD INSTRUCTIONS: 


If the song was saved to the Hard Drive of the PSR 9000 follow these steps. 

  1. Press Song I

Note: screen will say, “There is no disk- please insert disk”

  1. Press “popup” lower right corner of screen.
  2. Select “HD” under DEVICE.
  3. Press “Next” button

Note: Screen will show list of songs that are on the HD. Select songs from the list then press the “next” button. The screen will then show the title of the song.

Press the button to the side of the title of the song.

  1. Press Song recording under “Digital Recording”
  2. Press Song Creator
  3. Press Current Song
  4. Press Multi Track Record

Note: from this point the procedure is the same as above following step #9 above. Read the note following step 9 and proceed from there. 


+++++++++++++++++++++++++++++++++++++++++++++++++ 


Disk Operation 

To play a song that has been saved to disk: 

  1. Insert the disk that contains the song
  2. Press the Song I (see note at step # 3 above for location of this button)
  3. The Screen will display the songs that are on the disk
  4. Press the button to the side of the title of the song that you want to play.
  5. Press the Start Stop button to play the song.


------------------------------------------------------------------------


 

How to enter control changes while in Step Record. 

 

Primary reference page is 98 in the PSR 9000 Version 2 Owner's manual. 

{ After entering Song Creator and selecting Step Record.} 

Controller settings such as Volume, Pan, etc. can be edited using the Mixing Console. To enter the Mixing Console at this point Press the Mixing Console button located under the Digital Recording button - see illustration on page 122 of the manual. 

Once the Main Mixer screen comes up you can use the Next and Back buttons to navigate to the different control screens.

Page 123 gives a description of the various screens - Volume/EQ, Filter, Effect Depth, Tune, Voice and how to utilize the parameters in these screens. 

There is also an Effect Type Screen and a Master Equalizer Screen - see pages 124 and 125. 


-------------------------------------------------------------

How to record a song on the PSR 9000 


  1. Press Digital Recording/Song button
  2. Press the button to the left of Song Creator
  3. Press the button to the left of New Song
  4. Select either Quick Record or Multi Track Record.

Note: Quick record gives you 2 tracks - 1 for manual and 1 for accompaniment

Multi-Track gives you 16 tracks to record with. 

Quick Record: 

  1. Keyboard automatically selects Manual with the Accompaniment track disabled. If you want to record with out drums/accompaniment then leave the accompaniment track disabled.
  2. If you enable both the Manual and the Accompaniment tracks together you can record both tracks at the same time.


Multi Track Recording: 

  1. Each track is set up to record an R1 voice part.
  2. Enable the tracks that you wish to record.
  3. The D button will display the tracks listed (TR 9-16) when the D button is pressed. Notice that when the D button is pressed the tracks listed will change to TR 1-8 this means when you press the D button it will display those tracks.

Note: Tracks 1 - 8 are designed to record NON - accompaniment voices such as Right 1, Right 2, Right 3, Left voices. However tracks 9 - 16 can be programmed to record non-accompaniment voices as well. All that need be done is change the voice part above the track to the R1 or R2 or L setting. Refer to Owner's Manual. 

  1. Once the tracks have been selected choose the voices and effect settings that you wish to play with and also select the style of rhythm you with to work with.
  2. The on screen instructions state to press the Next button
  3. Press the Start/Stop button to begin recording.
  4. After the recording is finished press the Start/Stop button.

 

Note: If you wish to edit what you have played press the Next button and select Quantize, Track mix (only possible after 2 or more tracks have been recorded), Note shift. 

8. Make sure to press the Next button until you are in the Save/Delete window and save the data if you wish.